MOTOROLA VOICESURFR 28800 INTERNAL Card Type Modem (asynchronous) Chip Set Unidentified I/O Options Speaker out, microphone Maximum Modem Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Unidentified Fax Modulation Protocol Unidentified Error Correction/Compression Unidentified Fax Class Unidentified Data Bus 16-bit ISA Card Size Half-length, full-height card [Image] CONNECTIONS Function Label Function Label Line out (RJ-11) CN1 Speaker out CN3 Line in (RJ-11) CN2 Microphone CN4 USER CONFIGURABLE SETTINGS Function Label Position Factory configured - do not alter S6 Unidentified Factory configured - do not alter S7 Unidentified Factory configured - do not alter S8 Unidentified SERIAL PORT ADDRESS Setting S1 S2 COM1 (3F8h) Open Open COM2 (2F8h) Closed Open COM3 (3E8h) Open Closed COM4 (2E8h) Closed Closed INTERRUPT Setting S3 S4 S5 IRQ 3 Closed Open Open IRQ 4 Open Closed Open IRQ 5 Open Open Closed PLUG AND PLAY Plug & Play JP10 JP11 JP12 JP13 JP14 Enabled Closed Closed Closed Open Closed Disabled Open Open Open Closed Open SUPPORTED COMMAND SET Basic AT Commands AT, ‘+++’, A/ A, E, H, M, O, S, V, X, Y, Z &F, &V, &W, &Y, &Z Extended AT Commands \K, \Q %A, %C S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S26, S38 Note: See MHI Help File for full command documentation. Proprietary AT Command Set AUTO FALLFORWARD/FALLBACK Type: Configuration Format: AT [cmds] &An [cmds] Description: Controls the auto fallforward/fallback Command Function &A0 Disable auto fallforward/fallback &A1 Enable auto fallforward/fallback CONNECTION SPEED NEGOTIATION Type: Configuration Format: AT [cmds] &Hn [cmds] Description: Controls the connection speed negotiation Command Function &H0 V.34 connect speed negotiation (28.8Kbps-300bps) &H1 V.34 (28.8Kbps- 4800bps) &H2 V.32bis automatic (14.4Kbps -300bps) &H3 V.32bis only (14.4Kbps - 4800bps) &H4 V.32 automatic (9600-300bps) &H5 V.32 only (9600-4800bps) &H6 V.22 only (2400-1200bps) &H7 V.22 only (1200bps) &H8 212 only (1200bps) &H9 103 only (300bps) &H10 V.21 only (300bps) DATA CARRIER DETECT (DCD) Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Selects whether the DCD option is enabled or disabled Command Function &C0 DCD enabled &C1 DCD enabled after carrier signal detected &C2 Force DCD on and toggle DCD on disconnect DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected &S2 DSR high only while modem is connected &S3 DSR is forced high in all modes DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Note: The action each variant of &D causes depends on the setting of &Q Command Function &D0 Modem does not respond to DTR &D1 Modem goes to command mode after DTR goes is off &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. &D3 Modem is initialized after DTR goes off DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DL Re-dial last number DP Pulse dialing enabled DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports product code I1 Reports 000 I2 Reports OK or ERROR I3 Reports firmware revision number I4 Reports configuration settings RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables modem to send result codes to the DTE Command Function Q0 Result code sending enabled Q1 Result code sending disabled Q2 Call progress messages on originate only SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TRELLIS CODING Type: Configuration Format: AT [cmds] &Un [cmds] Description: Controls the trellis coding Command Function &U0 Enable trellis coding for V.32 mode at 9600bps &U1 Disable trellis coding for V.32 mode at 9600bps Extended AT Commands ANSWER MODE Type: Configuration Format: AT [cmds] %On [cmds] Description: Sets the answer mode Command Function %O0 Answer mode if ringing %O1 Forced to answer mode %O2 Automatic answer in originate mode AUTO-RELIABLE TIME BUFFER CONFIGURATION Type: Configuration Format: AT [cmds] \Cn [cmds] Description: Controls the handling of incoming data during auto-reliable time period Command Function \C0 Timeout and fallback, speed buffer, no data buffer \C1 Timeout and fallback, speed buffer, buffer receive data \C2 Auto reliable, fallback with fallback character, speed buffer, no receive data buffer \C3 Timeout and fallback, ITU-T V.14, buffer receive data \C4 Timeout and fallback with fallback character, ITU-T V.14, no data buffer BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Description: Sends break to modem Command Function \B0 6 data bits, no parity, 1 stop bit \B1 7N1 character length \B2 7P1 character length \B3 8P1 character length \B4 7P2 character length \B5 8P1 character length CALLER ID Type: Configuration Format: AT [cmds] #CC=n [cmds] Description: Controls the Caller ID function Command Function #CC=0 Caller ID disabled #CC=1 Caller ID displays formatted data #CC=2 Caller ID displays raw hexadecimal data CHARACTER ABORT Type: Configuration Format: AT [cmds] %Kn [cmds] Description: Controls the character abort Command Function %K0 Enable 2 second delay to character abort %K1 Disable delay to character abort COMPUTER - TO - MODEM SPEED SELECTION Type: Configuration Format: AT [cmds] \Tn [cmds] Description: Controls the computer- to - modem speed Command Function \T0 Autobaud \T1 Set speed to last AT command entry speed \T2 Force 300bps after connecting \T3 Force 1200bps after connecting \T4 Force 2400bps after connecting \T5 Force 4800bps after connecting \T6 Force 7200bps after connecting \T7 Force 9600bps after connecting \T8 Force 12.0bps after connecting \T9 Force 14.4bps after connecting \T10 Force 16.8bps after connecting \T11 Force 19.2bps after connecting \T12 Force 21.6bps after connecting \T13 Force 24.0bps after connecting \T14 Force 26.4bps after connecting \T15 Force 28.8bps after connecting \T16 Force 38.4bps after connecting \T17 Force 57.6bps after connecting \T18 Force 76.8bps after connecting \T19 Force 115.2bps after connecting \T20 Force 128.0bps after connecting CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 V.42 reliable mode enabled \N5 V.42, MNP reliable mode enabled \N6 Simulated controlled carrier DTR SIGNAL Type: Immediate Format: AT [cmds] %Zn [cmds] Description: Sets the DTR signal Command Function %Z0 Ignore DTR toggle %Z1 Dial stored phone number (0-3) on DTR toggle %Z2 Attempt to connect on DTR toggle EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Connect and protocol message reports modem - to - modem speed \V1 Connect and protocol message reports computer - to - modem speed \V2 Connect message reports computer - to - modem speed/V.42 error correction \V3 Connect message reports computer - to - modem speed FLOW CONTROL Type: Configuration Format: AT [cmds] \Gn [cmds] Description: Selects modem port flow control Command Function \G0 Flow control disabled \G1 XON/XOFF flow control enabled \G2 XON/XOFF flow control only for transmitting data \G3 XON/XOFF flow control with pass-through enabled PARITY Type: Immediate Format: AT [cmds] \P [cmds] Description: Controls parity Command Function \P0 Even Parity \P1 Space \P2 Odd \P3 Mark \P4 Automatic RETRAIN Type: Immediate Format: AT [cmds] %Q [cmds] Description: Sets the retrain Command Function %Q0 Disable retrain %Q1 Attempt up to 3 retrains and disconnect if unsuccessful %Q2 Retrain until signal quality is good RETURN CALL PROGRESS MESSAGE SPEED Type: Immediate Format: AT [cmds] %R [cmds] Description: Sets the return call progress message speed Command Function %R0 Return call progress message at current computer - to - modem speed %R1 Return call progress message at last computer- to - modem speed %R2 Return call progress message at 300bps %R3 Return call progress message at 1200bps %R4 Return call progress message at 2400bps %R5 Return call progress message at 4800bps %R6 Return call progress message at 7200bps %R7 Return call progress message at 9600bps %R8 Return call progress message at 12.0bps %R9 Return call progress message at 14.4bps %R10 Return call progress message at 16.8bps %R11 Return call progress message at 19.2bps %R12 Return call progress message at 21.6bps %R13 Return call progress message at 24.0bps %R14 Return call progress message at 26.4bps %R15 Return call progress message at 28.8bps %R16 Return call progress message at 38.4bps %R17 Return call progress message at 57.6bps %R18 Return call progress message at 76.8bps %R19 Return call progress message at 115.2bps %R20 Return call progress message at 128.0bps S(status) -REGISTERS RETRANSMISSION COUNTER Type: Register Format AT [cmds] S70=n [cmds] Default: 100 Range: 0-255 Description: Sets the retransmission counter